Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a straightforward process that can be completed in just a few procedures.

• Initially ensuring your red dot sight is turned on.
• Locate the small reinitialize button on the side of the unit.
• Utilize a thin tool to press and hold the reset button for approximately 5 seconds.
• Release the switch and your Holosun EPS Carry Red Dot sight will reboot.
• The red dot sight should now be reverted to its factory settings.

Reset Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to its factory configuration is a breeze. First, locate the tiny button on the bottom of your optic. Then, press and hold it for around five seconds until you see a brief flash. Your Holosun check here EPS Carry is now reverted to its factory settings, ready for accurate shooting.

revive your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Simultaneously press and hold the power button for approximately 7 seconds.
• The display will flash, indicating that the reset is successfuly initiated.
• Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and confirm your sight's functionality. If you encounter any further troubles, don't hesitate to reach out to their technical assistance.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• Initially, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, tap the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry with a Factory Original Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the answer. This will restore your sight to its initial settings, clearing any custom configurations you've made. To execute this reset, observe these straightforward steps:

• First, find the reset button on your EPS Carry.
• Next, use a fine object, like a paperclip, to push the reset switch.
• During keep the reset lever pressed, power on your EPS Carry.
• You'll blink a message confirming that the reset is successful.

After the reset is complete, your EPS Carry will be set to its factory settings.

Report this wiki page